|
Construction Of The World Trade Center
|
The structural engineering firm Worthington, Skilling, Helle & Jackson worked to implement Yamasaki's design, developing the tube-frame structural system used in the twin towers. The Port Authority's Engineering Department served as foundation engineers, Joseph R. Loring & Associates as electrical engineers, and Jaros, Baum & Bolles as mechanical engineers. Tishman Realty & Construction Company was the general contractor on the World Trade Center project. Guy F. Tozzoli, director of the World Trade Department at the Port Authority, and Rino M. Monti, the Port Authority's Chief Engineer, oversaw the project. As an interstate agency, the Port Authority was not subject to local laws and regulations of the City of New York including building codes. Nonetheless, the structural engineers of the World Trade Center ended up following draft versions of the new 1968 building codes. The tube-frame design, earlier introduced by Fazlur Khan, was a new approach that allowed more open floor plans than the traditional design that distributed columns throughout the interior to support building loads. The World Trade Center towers used high-strength, load-bearing perimeter steel columns called Vierendeel trusses that were spaced closely together to form a strong, rigid wall structure, supporting virtually all lateral loads such as wind loads, and sharing the gravity load with the core columns. The perimeter structure containing 59 columns per side was constructed with extensive use of prefabricated modular pieces each consisting of three columns, three stories tall, connected by spandrel plates. The spandrel plates were welded to the columns to create the modular pieces off-site at the fabrication shop. Adjacent modules were bolted together with the splices occurring at mid-span of the columns and spandrels. The spandrel plates were located at each floor, transmitting shear stress between columns, allowing them to work together in resisting lateral loads. The joints between modules were staggered vertically so the column splices between adjacent modules were not at the same floor.
The core of the towers housed the elevator and utility shafts, restrooms, three stairwells, and other support spaces. The core of each tower was a rectangular area 87 by 135 feet (27 by 41 m) and contained 47 steel columns running from the bedrock to the top of the tower. The large, column-free space between the perimeter and core was bridged by prefabricated floor trusses. The floors supported their own weight as well as live loads, providing lateral stability to the exterior walls and distributing wind loads among the exterior walls. The floors consisted of 4 inches (10 cm) thick lightweight concrete slabs laid on a fluted steel deck. A grid of lightweight bridging trusses and main trusses supported the floors. The trusses connected to the perimeter at alternate columns and were on 6 foot 8 inch (2.03 m) centers. The top chords of the trusses were bolted to seats welded to the spandrels on the exterior side and a channel welded to the core columns on the interior side. The floors were connected to the perimeter spandrel plates with viscoelastic dampers that helped reduce the amount of sway felt by building occupants.
Hat trusses (or "outrigger truss") located from the 107th floor to the top of the buildings were designed to support a tall communication antenna on top of each building. Only 1 WTC (north tower) actually had an antenna fitted; it was added in 1978. The truss system consisted of six trusses along the long axis of the core and four along the short axis. This truss system allowed some load redistribution between the perimeter and core columns and supported the transmission tower.
The tube frame design using steel core and perimeter columns protected with sprayed-on fire resistant material created a relatively lightweight structure that would sway more in response to the wind compared to traditional structures such as the Empire State Building that have thick, heavy masonry for fireproofing of steel structural elements. During the design process, wind tunnel tests were done to establish design wind pressures that the World Trade Center towers could be subjected to and structural response to those forces. Experiments also were done to evaluate how much sway occupants could comfortably tolerate, however, many subjects experienced dizziness and other ill effects. One of the chief engineers Leslie Robertson worked with Canadian engineer Alan G. Davenport to develop viscoelastic dampers to absorb some of the sway. These viscoelastic dampers, used throughout the structures at the joints between floor trusses and perimeter columns along with some other structural modifications, reduced the building sway to an acceptable level.
|
|